BRITE
BOX
BRITE BOX™ FOGSTER SD7 - INSTALLATION INSTRUCTIONS
www.thebritebox.com
The BRITE BOX FOGSTER is a fully self contained device that illuminates your factory installed fog lights when your high beams
are on. This provides you with an even carpet of light that stretches from near to far. Without Brite Box Fogster, the fog lights
drop out when your high beams are on. With Brite Box Fogster, you can enjoy the benefits of this improved beam pattern,
automatically, without placing any additional loads on the vehicle's stock headlight switches or wiring.
Installing your Fogster is easily accomplished with common hand tools in a short period of time. In order to make your installa-
tion go as smoothly as possible, it is recommended that you read the instructions and plan your installation before starting.
PARTS LIST:
1 - Brite Box Fogster SD7
1- 15 Amp ATC Fuse
12- Cable (Wire) Ties
1 - Alcohol Pad
TOOLS REQUIRED:
Wrench to fit your positive battery post / clamp - usually a 10mm, 13mm, or 1/2 inch.
10 mm Socket, Socket Wrench, Long extension
Philips Screwdriver
Medium slotted screwdriver
Masking or Duct Tape
STEP 1: UNBOLT HEADLIGHT ON DRIVER'S SIDE OF VEHICLE.
Figure Reference: Figure 2
Remove two (2) plastic clips as shown in FIG 2. that secures rubber trim piece to vehicle. Use Philips screwdriver to unscrew
center section. When center section is removed, clips will pull straight out .
" Remove three (3) 10mm bolts in positions shown in FIG 2.
" Bottom bolt is located under headlight and will require you to use a long socket extension to reach it. Take care not to drop
this bolt when you remove it.
" Please note that some (NOT ALL) trucks have a sensor bolted to the driver side headlight assembly in location indicated in FIG
2. If your vehicle, has this sensor, simply let it dangle until you reinstall headlight.
STEP 2: REMOVE HEADLIGHT
Figure Reference: Figure 3
" There is a "pop" clip that holds the headlight in even though it is unbolted.
" Releasing this clip requires that you pry the headlight forward at the location indicated in FIG 3.
" Use masking or duct tape to PAD the shaft of your screwdriver to avoid damaging the headlight or fender of vehicle. Insert
screwdriver between fender and headlight and GENTLY pry it forward. Headlight will pop free from vehicle.
" When headlight is free, unplug headlight harness from headlight bulb (blue connector) and remove side marker bulb from
headlight assembly by twisting it.
" Place headlight where it cannot be damaged while you are installing Brite Box Fogster.
STEP 3: INSTALL BRITE BOX FOGSTER BEHIND HEADLIGHT
Figure Reference: Figure 1
" Plug vehicle's headlight plug (removed in Step 2) into receptacle of Brite Box.
" Mount Brite Box Fogster to vehicle using double stick tape (clean surface tape will mount to with supplied alcohol pad) or by
wire tying it to an existing harness. Make sure you mount Brite Box Fogster far enough back so as to allow headlight to be
reinstalled.
" Be sure to observe UP orientation on Brite Box Fogster's label to allow for drainage should water enter unit. NOTE: Water
damage is not covered under warranty!
STEP 3: POLARIZE FOG LIGHT HARNESS: Plug Brite Box's single brown wire into fog light harness wire in the following manner:
TRUCKS WHERE FOG LIGHTS WERE INSTALLED BY FACTORY:
Plug BROWN single wire from Brite Box into BROWN wire in fog light harness.
TRUCKS WHERE FOG LIGHTS WERE ADDED USING MOPAR FOG LIGHT KIT: Plug BROWN single wire from Brite Box into BLACK wire in
fog light harness.
STEP 4: PLUG IN BRITE BOX FOGSTER'S FOG LIGHT HARNESS
Figure Reference: NONE
" Run fog light harness (see Fig. 1) to fog light in bumper.
" Unplug vehicle's two prong connector from fog light bulb and plug it into female side of fog light harness.
" Plug remaining male connector of fog light harness into fog light bulb.
U.S. Pat. Pend.
Made In U.S.A.
Plug
Receptacle
Fog Light
Harness
FIGURE 1
(28 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels