Beam RST825 SatRADIO Manuel d'utilisateur télécharger pdf

0xxx

RST825

SatRADIO

Quick

Start

Guide

Beam Communications Pty Ltd

8 Anzed Court, Mulgrave

Victoria, Australia, 3170

T: +61 3 8851 0400

F: +61 3 9560 9055

E: [email protected]

W: www.beamcomm.net

Iridium is a line-of-sight Satellite network, conditions that can

compromise the quality of the service you may receive include:

Optimising Iridium performance

More info @

www.beamcomm.net

1. Obstructions: Provide the best satellite view for your antenna by removing all obstructions where possible

2. Cabling: Use the shortest cable length and the fewest number of connectors on all Iridium certified antenna cable runs

3. RF Interference: Install antenna as far away from other transmitters as possible.

Package Contents

Before commencing installation ensure your package

has the following components:

1. Install SIM card

2. Getting started

3. Making calls...

Thank you for purchasing the BEAM

RST825 SatRADIO

his QuickStart Guide install

your

T lists the steps to

BEAM Satellite equipment:

Installing your SIM card

The RST825 requires that an active Iridium or Telstra Mobile Satellite

SIM card to be installed. This is not included with this RST825 kit.

Refer to your place of purchase if you do not have an active SIM card enabled to

make Iridium Satellite calls.

Tools required:

1. Philips-head screwdriver 2. Allen Key (supplied)

Follow the instructions below to install your SIM card:

Unscrew holding screw Slide panel RIGHT Locate SIM cover Unscrew with 2mm Allen Key

5. Slide the top black clip back towards you. 6. Flick this clip up to expose the rails to slide the SIM into(7).

8. Gently push down on the grey SIM housing and push away from you to LOCK the SIM in place.

Replace covers by following steps 4 to 1.

NOTE: Metallic SIM contacts must be face-down to engage with the SIM card reader.

1 2 3 4

5 6 7 8

1 x SatRADIO unit in rugged case

1 x Iridium Handset with curly cord

1 x RST915 magnetic-mount Iridium antenna with 5m cable

1 x Radio Handset with curly cord

1 x 110V/240V IEC AC power lead

1 x DC power cable

1 x Hex-Wrench for SIM cover

1 x Printed user manual

1 x Printed Iridium Antenna Guide

Accessing Speed Dials form Radio Handset

The quick-dial mechanism can also be used if any of the quick-dial numbers have been setup in the SatRADIO. Dial PIN, then a

digit between 0->9 then *, to identify the quick dial number. The quick dials can be programmed only using the Beam

Management System when connected with a PC to the configuration port.

The quick dials are accessed in the following way;

1. Ensure the quick dial locations have been programmed in the main satellite terminal

2. Enter the PIN from the handset as per above instructions

3. Once acceptance pips received enter a Qucik Dial location digit between 0->9 then *, obviously only those locations that

have been preconfigured can be called in this manner.

For example if you enter your PIN followed by 2 * this would dial the preset Quick Dial in location 2

Answering a call

There are two ways of answering a call on the two-way radio, by either using the DTMF controls on the handheld to accept the

call or if you want all incoming calls answered automatically. This can be configured on the terminal.

Answering on a Radio

A RING signal will be intermittently transmitted on the Radio channel and the handheld user can reply to answer the incoming

call by sending a DTMF-0 to answer the incoming call.

Note: The DTMF-0 must be sent in the gap between rings for it to be heard by SatRADIO.

Auto Answer

The firmware can be set to automatically auto-answer an incoming call as long as the Radio is On.

Note: Auto answer cannot work concurrently with Autodial being ON

Using Autodial Mode

This mode enables the RST825 to continuously maintain a phone call link to either the last dialed destination or the Quick Dial

position “0” if configured that way. This is ideal for emergency or disaster recovery situations when the terminal may be being

used as a primary communication tool or a replacement for a Radio link that is down.

Setting up Autodial feature

The Auto-dial switch indicates to the SatRADIO that a number is to be auto-(re)dialed once the Radio is turned on

There are two means of setting an Autodial number into the system

1/ Last number dialled

2/ Quick Dial location “0” ( zero)

Last number dialed

The last number dialled is simply the last number dialled on the SatRADIO either via the Iridium handset or the DTMF radio.

This provides the most convenient means of having an easily changeable number, however caution must be exercised as the

Autodial switch will automatically dial as soon as activated. To check the last number dialled simply take the handset from the

cradle and press the OK button this will display the last number dialled. To enter a new number simply enter the number in

the full dialing sequence and then press OK

Now as soon as the Autodial switch is activated this is the number that will be continually attempted to be called. If at any time

the call drops out the system will automatically redial in order to re-establish the call within 20 30 seconds.

Quick Dial - Autodial

The Quick Dial Autodial feature uses the Quick Dial memory location “0” of the satellite terminal. This enables a fixed number

to be programmed for permanent application where the SatRADIO is always to call the same location. This is PIN protected

using the Beam Management System and can only be changed by an authorized person.

So long as the main terminal has been set up for Quick Dial with a number programmed into location “0” then as soon as

Autodial is switched ON then the system will automatically and continually maintain a call with the preset number.

Hanging Up: To deactivate Autodial switch Autodial button to OFF or alternatively switch the Satellite Terminal to OFF.

SIM

Socket

1 2

SatRADIO 1
your BEAM RST825 SatRADIO 2

Résumé du contenu

Page 1 - SatRADIO

USRMAN000xxxRST825SatRADIOQuickStart GuideBeam Communications Pty Ltd8 Anzed Court, MulgraveVictoria, Australia, 3170T: +61 3 8851 0400F: +61 3 95

Page 2 - your BEAM RST825 SatRADIO

Handset Mode Transferred to Radio ModeIt is possible to make a call on the Intelligent Satellite handset and then place the handset back into the crad

Plus de documents pour Téléphones Beam RST825 SatRADIO

Voir le document Beam RST825 SatRADIO Manuel d'installation

Beam RST825 SatRADIO Manuel d'installation (30 pages)

Voir le document Beam RST825 SatRADIO Manuel d'utilisateur

Beam RST825 SatRADIO Manuel d'utilisateur (5 pages)

Commentaires sur ces manuels

Pas de commentaire

Beam RST825 SatRADIO Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Téléphones Beam RST825 SatRADIO. Beam RST825 SatRADIO User manual Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Téléphones Beam RST825 SatRADIO

Commentaires sur ces manuels

Produits connexes et manuels pour Téléphones Beam RST825 SatRADIO